=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.05.29 23:19:15 =~=~=~=~=~=~=~=~=~=~=~= DTS-TEST-SEQNO = 80 VR9 # VR9 # tftp initramfs Using vr9 Switch device TFTP from server 192.168.2.100; our IP address is 192.168.2.1 Filename 'initramfs'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### done Bytes transferred = 5881830 (59bfe6 hex) VR9 # VR9 # bootm ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS OpenWrt Linux-linux-3.18.14 Created: 2015-05-29 21:18:54 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5881766 Bytes = 5.6 MiB Load Address: 80002000 Entry Point: 80002000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 3.18.14 (arny@e6420) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45704) ) #28 Thu May 28 22:03:55 CEST 2015 [ 0.000000] SoC: VR9 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] MIPS: machine is VGV952CJW33-E-IR - EasyBox 904 xDSL [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit panic=1 DTS-TEST-SEQNO=80 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0000d180 [ 0.000000] Readback ErrCtl register=0000d180 [ 0.000000] Memory: 120812K/131072K available (3312K kernel code, 145K rwdata, 932K rodata, 4424K init, 204K bss, 10260K reserved) [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 500MHz [ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.044000] pinctrl core: initialized pinctrl subsystem [ 0.048000] NET: Registered protocol family 16 [ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done [ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [ 0.164000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [ 0.168000] PCI host bridge /fpi@10000000/pci@E105400 ranges: [ 0.172000] MEM 0x0000000018000000..0x0000000019ffffff [ 0.176000] IO 0x000000001ae00000..0x000000001affffff [ 0.388000] ifx_pcie_wait_phy_link_up timeout [ 0.600000] ifx_pcie_wait_phy_link_up timeout [ 0.812000] ifx_pcie_wait_phy_link_up timeout [ 1.024000] ifx_pcie_wait_phy_link_up timeout [ 1.236000] ifx_pcie_wait_phy_link_up timeout [ 1.240000] pcie_rc_initialize link up failed!!!!! [ 1.264000] gpio-stp-xway 1e100bb0.stp: Init done [ 1.268000] usbcore: registered new interface driver usbfs [ 1.272000] usbcore: registered new interface driver hub [ 1.276000] usbcore: registered new device driver usb [ 1.280000] PCI host bridge to bus 0000:00 [ 1.284000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 1.288000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 1.292000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.296000] Switched to clocksource MIPS [ 1.300000] NET: Registered protocol family 2 [ 1.304000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.312000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 1.320000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.324000] TCP: reno registered [ 1.328000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 1.332000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 1.340000] NET: Registered protocol family 1 [ 2.100000] gptu: totally 6 16-bit timers/counters [ 2.104000] gptu: misc_register on minor 63 [ 2.108000] gptu: succeeded to request irq 126 [ 2.112000] gptu: succeeded to request irq 127 [ 2.116000] gptu: succeeded to request irq 128 [ 2.124000] gptu: succeeded to request irq 129 [ 2.128000] gptu: succeeded to request irq 130 [ 2.132000] gptu: succeeded to request irq 131 [ 2.136000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin [ 2.144000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 6860000 [ 2.152000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 6860000 [ 2.256000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 2.268000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.284000] msgmni has been set to 235 [ 2.288000] io scheduler noop registered [ 2.292000] io scheduler deadline registered (default) [ 2.300000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 2.308000] console [ttyLTQ0] enabled [ 2.308000] console [ttyLTQ0] enabled [ 2.316000] bootconsole [early0] disabled [ 2.316000] bootconsole [early0] disabled [ 2.324000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc [ 2.324000] nand: Samsung NAND 512MiB 3,3V 8-bit [ 2.324000] nand: 512MiB, SLC, page size: 2048, OOB size: 64 [ 2.340000] Scanning device for bad blocks [ 2.376000] Bad eraseblock 528 at 0x000004200000 [ 2.516000] Bad eraseblock 2582 at 0x0000142c0000 [ 2.616000] 16 ofpart partitions found on MTD device 14000000.nand-parts [ 2.620000] Creating 16 MTD partitions on "14000000.nand-parts": [ 2.628000] 0x000000000000-0x000000040000 : "uboot" [ 2.632000] 0x000000040000-0x000003c40000 : "rootfs1" [ 2.640000] 0x000003c40000-0x000004140000 : "kernel1" [ 2.644000] 0x000004140000-0x000004240000 : "tmp1" [ 2.648000] 0x000004240000-0x000004440000 : "tmp2" [ 2.652000] 0x000004440000-0x000004540000 : "sysconfig" [ 2.656000] 0x000004540000-0x000004640000 : "ubootconfig" [ 2.664000] 0x000004640000-0x000004700000 : "fwdiag" [ 2.668000] 0x000004700000-0x000004a00000 : "lcdimage" [ 2.672000] 0x000004a00000-0x000004b00000 : "mfgconfig" [ 2.680000] 0x000004b00000-0x000004c00000 : "sipdata" [ 2.684000] 0x000004c00000-0x000008c00000 : "voice" [ 2.688000] 0x000008c00000-0x00001be00000 : "misc" [ 2.696000] 0x00001be00000-0x00001fa00000 : "rootfs2" [ 2.700000] 0x00001fa00000-0x00001ff00000 : "kernel2" [ 2.704000] 0x00001ff00000-0x000020000000 : "mystery" [ 2.812000] libphy: lantiq,xrx200-mdio: probed [ 2.836000] net-xrx200: invalid MAC, using random [ 2.840000] eth0 (uninitialized): no PHY found [ 2.844000] xrx200-mdio: probing phy of port 0 failed [ 2.848000] eth0 (uninitialized): no PHY found [ 2.852000] xrx200-mdio: probing phy of port 1 failed [ 2.924000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1) [ 2.992000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1) [ 2.996000] eth0 (uninitialized): no PHY found [ 3.000000] xrx200-mdio: probing phy of port 5 failed [ 3.008000] wdt 1f8803f0.watchdog: Init done [ 3.012000] TCP: cubic registered [ 3.016000] NET: Registered protocol family 17 [ 3.020000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.032000] 8021q: 802.1Q VLAN Support v1.8 [ 3.052000] Freeing unused kernel memory: 4424K (8044e000 - 808a0000) [ 3.076000] init: Console is alive [ 3.080000] init: - watchdog - [ 3.104000] SCSI subsystem initialized [ 3.116000] dwc2 1e101000.ifxhcd: requested GPIO 489 [ 3.980000] dwc2 1e101000.ifxhcd: DWC OTG Controller [ 3.980000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1 [ 3.988000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000 [ 3.996000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode - [ 3.996000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode. [ 4.008000] hub 1-0:1.0: USB hub found [ 4.012000] hub 1-0:1.0: 1 port detected [ 4.876000] dwc2 1e106000.ifxhcd: DWC OTG Controller [ 4.876000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2 [ 4.884000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000 [ 4.892000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode - [ 4.892000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode. [ 4.904000] hub 2-0:1.0: USB hub found [ 4.908000] hub 2-0:1.0: 1 port detected [ 4.916000] usbcore: registered new interface driver usb-storage [ 5.084000] init: - preinit - [ 5.216000] random: mktemp urandom read with 20 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.308000] procd: - early - [ 8.312000] procd: - watchdog - [ 8.924000] procd: - ubus - [ 9.936000] procd: - init - Please press Enter to activate this console. [ 10.632000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH [ 10.656000] NET: Registered protocol family 10 [ 10.668000] NET: Registered protocol family 8 [ 10.672000] NET: Registered protocol family 20 [ 10.688000] PPP generic driver version 2.4.2 [ 10.704000] MEI CPE Driver, Version 1.2.0 [ 10.708000] (c) Copyright 2009, Infineon Technologies AG [ 10.708000] ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ### Lantiq CPE API Driver version: DSL CPE API V4.11.4 [ 10.728000] [ 10.728000] Predefined debug level: 2 [ 10.736000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 10.744000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 10.764000] cfg80211: Calling CRDA to update world regulatory domain [ 10.780000] cfg80211: World regulatory domain updated: [ 10.784000] cfg80211: DFS Master region: unset [ 10.788000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 10.796000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.804000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.812000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 10.820000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 10.828000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 10.840000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 10.848000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 10.856000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 10.960000] Infineon Technologies DEU driver version 2.0.0 [ 10.964000] IFX DEU DES initialized (multiblock). [ 10.968000] IFX DEU AES initialized (multiblock). [ 10.972000] IFX DEU ARC4 initialized (multiblock). [ 10.976000] IFX DEU SHA1 initialized. [ 10.980000] IFX DEU MD5 initialized. [ 10.984000] IFX DEU SHA1_HMAC initialized. [ 10.988000] IFX DEU MD5_HMAC initialized. [ 10.996000] NET: Registered protocol family 24 ioctl ATM_SETESI: No such device [ 13.928000] PTM 1.0.27 PTM (E1) firmware version 0.30 [ 13.932000] ifxmips_ptm: PTM init succeed [ 15.292000] device eth0 entered promiscuous mode [ 15.300000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 32.280000] random: nonblocking pool is initialized BusyBox v1.23.2 (2015-05-24 15:32:08 CEST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r45810) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:/# root@OpenWrt:/# lcpci root@OpenWrt:/# root@OpenWrt:/# lsusb Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@OpenWrt:/# root@OpenWrt:/# ifconfig -a br-lan Link encap:Ethernet HWaddr 36:02:3B:0E:36:4D inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fda5:96a1:ff3c::1/60 Scope:Global UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:322 (322.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 36:02:3B:0E:36:4D UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:677 (677.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3936 (3.8 KiB) TX bytes:3936 (3.8 KiB) nas0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ptm0 Link encap:Ethernet HWaddr 00:20:DA:86:23:75 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:/# root@OpenWrt:/# ifconfig br-lan 192.168.2.1 root@OpenWrt:/# ping 192.168.2.100 PING 192.168.2.100 (192.168.2.100): 56 data bytes ^C --- 192.168.2.100 ping statistics --- 29 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:/# root@OpenWrt:/# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:0 link:up speed:1000baseT full-duplex auto Port 1: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:1 link:down Port 2: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:2 link:down Port 3: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:3 link:down Port 4: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:4 link:down Port 5: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:5 link:down Port 6: uvr: 0 vsr: 0 vinr: 0 tvm: 0 pvid: 0 link: port:6 link:up speed:1000baseT full-duplex auto root@OpenWrt:/# root@OpenWrt:/#