ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 00000008 DDR autotuning Rev 0.3c DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-Lv2.0.40-A0.5 (Feb 12 2015 - 23:05:42) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) 512 MiB Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: Bad block at 0x000004200000 nand_read_bbt: Bad block at 0x0000142c0000 In: serial Out: serial Err: serial Net: Internal phy(GE) firmware version: 0x040b vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 1  0 please input password : VR9 # printenv console console=ttyS0 VR9 # help ? - alias for 'help' base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol cal - address calculation cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console go - start application at address 'addr' help - print command description/usage httpd - start http server lcd - lcd sub-system loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mdio - mdio read and write mm - memory modify (auto-incrementing address) mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables sleep - delay execution for some time smi - smi read and write sw - switch operation tftpboot- boot image via network using TFTP protocol unsetenv- delete environment variables upgrade - upgrade - forward/backward copy memory to pre-defined flash location version - print monitor version VR9 # reset ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 00000008 DDR autotuning Rev 0.3c DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-Lv2.0.40-A0.5 (Feb 12 2015 - 23:05:42) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) 512 MiB Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: Bad block at 0x000004200000 nand_read_bbt: Bad block at 0x0000142c0000 In: serial Out: serial Err: serial Net: Internal phy(GE) firmware version: 0x040b vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 1  0 Uncompressing LCD bootup images ............... NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000 0x300000 bytes read: OK 1. bootid : 0, bootnum : 0 Writing to Nand... Erasing at 0x4540000 -- 50% complete.Erasing at 0x4560000 -- 100% complete. done 2. bootid : 0, bootnum : 1 NAND read: device 0 offset 0x0000000003c40000, size 0x0000000000500000 0x500000 bytes read: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-2.6.32.32 Created: 2015-04-20 2:24:05 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1572800 Bytes = 1.5 MiB Load Address: 80002000 Entry Point: 800061b0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Lantiq xDSL CPE VR9 mips_hpt_frequency = 250000000, counter_resolution = 2 [ 0.000000] Linux version 2.6.32.32 (ben_chang@SW3SS01) (gcc version 4.3.3 (GCC) ) #2 Wed Apr 15 15:31:34 CST 2015 [ 0.000000] phym = 08000000, mem = 07400000, max_pfn = 00007400 [ 0.000000] Reserving memory for CP1 @0xa7400000, size 0x00c00000 [ 0.000000] CPU revision is: 00019556 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 07400000 @ 00000000 (usable) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00007400 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00007400 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 29464 [ 0.000000] Kernel command line: root=/dev/mtdblock1 rw rootfstype=squashfs,jffs2 ip=192.168.2.1:192.168.2.100::::eth0:on console=ttyS0,115200 ethaddr=88:03:55:E2:84:74 phym=128M mem=116M panic=1 mtdparts=ifx_nand:256k(uboot),60m(rootfs),5m(kernel),1m(tmp1),2m(tmp2),1m(sysconfig),1m(ubootconfig),768k(fwdiag),3m(lcdimage),1m(mfgconfig),1m(sipdata),64m(voice),306m(misc),60m(rootfs2),5m(kernel2) init=/etc/preinit vpe1_load_addr=0x87e00000 vpe1_mem=2M [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0000f180 [ 0.000000] Readback ErrCtl register=0000f180 [ 0.000000] Memory: 112696k/118784k available (3378k kernel code, 5924k reserved, 948k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:185 [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] console [ttyS0] enabled [ 0.030000] Calibrating delay loop... 331.77 BogoMIPS (lpj=165888) [ 0.053000] Security Framework initialized [ 0.054000] Mount-cache hash table entries: 512 [ 0.061000] NET: Registered protocol family 16 [ 0.076000] bio: create slab at 0 [ 0.079000] SCSI subsystem initialized [ 0.081000] NET: Registered protocol family 8 [ 0.082000] NET: Registered protocol family 20 [ 0.083000] cfg80211: Using static regulatory domain info [ 0.084000] cfg80211: Regulatory domain: US [ 0.085000] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.086000] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.087000] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.088000] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.089000] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.090000] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.091000] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.092000] cfg80211: Calling CRDA for country: US [ 0.093000] Switching to clocksource MIPS [ 0.096000] NET: Registered protocol family 2 [ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.107000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.113000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.120000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.126000] TCP reno registered [ 0.129000] NET: Registered protocol family 1 [ 0.134000] gptu: totally 6 16-bit timers/counters [ 0.139000] gptu: misc_register on minor 63 [ 0.142000] gptu: succeeded to request irq 118 [ 0.147000] gptu: succeeded to request irq 119 [ 0.151000] gptu: succeeded to request irq 120 [ 0.156000] gptu: succeeded to request irq 121 [ 0.160000] gptu: succeeded to request irq 122 [ 0.165000] gptu: succeeded to request irq 123 [ 0.169000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 [ 0.169000] ,(c)2009 Infineon Technologies AG [ 0.179000] Lantiq CGU driver, version 1.1.27, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.187000] vpe1_mem = 200000 [ 0.190000] Wired TLB entries for Linux read_c0_wired() = 0 [ 0.198000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.203000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.209000] yaffs Apr 15 2015 15:26:09 Installing. [ 0.213000] msgmni has been set to 220 [ 0.218000] Line: 127, function: deu_init [ 0.221000] Infineon Technologies DEU driver version 2.0.0 [ 0.227000] IFX DEU DES initialized (multiblock). [ 0.232000] IFX DEU AES initialized (multiblock). [ 0.236000] IFX DEU ARC4 initialized (multiblock). [ 0.241000] IFX DEU SHA1 initialized. [ 0.245000] IFX DEU MD5 initialized. [ 0.248000] IFX DEU SHA1_HMAC initialized. [ 0.252000] IFX DEU MD5_HMAC initialized. [ 0.256000] io scheduler noop registered (default) [ 0.267000] ifx_pmu_init: Major 252 [ 0.270000] Lantiq PMU driver, version 1.2.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.277000] [ 0.277000] ======= ifx_gpio_register (1,TEST) ======= kernel init [ 0.285000] [ 0.285000] ======= ifx_gpio_register (2,MEI) ======= kernel init [ 0.292000] [ 0.292000] ======= ifx_gpio_register (3,DSL-NTR) ======= kernel init [ 0.300000] [ 0.300000] ======= ifx_gpio_register (4,SSC) ======= kernel init [ 0.308000] [ 0.308000] ======= ifx_gpio_register (5,ASC0) ======= kernel init [ 0.315000] [ 0.315000] ======= ifx_gpio_register (6,SDIO) ======= kernel init [ 0.323000] [ 0.323000] ======= ifx_gpio_register (7,LEDC) ======= kernel init [ 0.331000] [ 0.331000] ======= ifx_gpio_register (8,USB) ======= kernel init [ 0.338000] [ 0.338000] ======= ifx_gpio_register (9,INT_SW) ======= kernel init [ 0.346000] [ 0.346000] ======= ifx_gpio_register (10,PCI) ======= kernel init [ 0.354000] [ 0.354000] ======= ifx_gpio_register (11,PCIE) ======= kernel init [ 0.361000] [ 0.361000] ======= ifx_gpio_register (12,NAND) ======= kernel init [ 0.369000] [ 0.369000] ======= ifx_gpio_register (13,PPA) ======= kernel init [ 0.377000] [ 0.377000] ======= ifx_gpio_register (14,TAPI-VMMC) ======= kernel init [ 0.385000] [ 0.385000] ======= ifx_gpio_register (15,TAPI-DEMO) ======= kernel init [ 0.393000] [ 0.393000] ======= ifx_gpio_register (16,TAPI-FXO) ======= kernel init [ 0.401000] [ 0.401000] ======= ifx_gpio_register (17,TAPI-DXT) ======= kernel init [ 0.409000] [ 0.409000] ======= ifx_gpio_register (18,TAPI-VCPE) ======= kernel init [ 0.417000] [ 0.417000] ======= ifx_gpio_register (19,VINAX) ======= kernel init [ 0.425000] [ 0.425000] ======= ifx_gpio_register (20,USIF-UART) ======= kernel init [ 0.433000] [ 0.433000] ======= ifx_gpio_register (21,USIF-SPI) ======= kernel init [ 0.442000] [ 0.442000] ======= ifx_gpio_register (22,SFLASH) ======= kernel init [ 0.449000] [ 0.449000] ======= ifx_gpio_register (23,EEPROM) ======= kernel init [ 0.457000] [ 0.457000] ======= ifx_gpio_register (24,USIF-SFLASH) ======= kernel init [ 0.466000] [ 0.466000] ======= ifx_gpio_register (25,LED) ======= kernel init [ 0.473000] [ 0.473000] ======= ifx_gpio_register (26,EBU_LED) ======= kernel init [ 0.481000] [ 0.481000] ======= ifx_gpio_register (27,EXIN) ======= kernel init [ 0.489000] [ 0.489000] ======= ifx_gpio_register (28,PAGE_BUTTON) ======= kernel init [ 0.497000] [ 0.497000] ======= ifx_gpio_register (29,DECT) ======= kernel init [ 0.505000] [ 0.505000] ======= ifx_gpio_register (30,SERIAL_IN) ======= kernel init [ 0.513000] [ 0.513000] ======= ifx_gpio_register (31,BUTTON) ======= kernel init [ 0.521000] [ 0.521000] ======= ifx_gpio_register (32,LCD) ======= kernel init [ 0.529000] [ 0.529000] ======= ifx_gpio_register (33,TP) ======= kernel init [ 0.536000] [ 0.536000] ======= ifx_gpio_register (34,SIPO) ======= kernel init [ 0.544000] Lantiq GPIO driver, version 1.2.14, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.552000] Infineon Technologies RCU driver version 1.0.8 [ 0.557000] [ 0.557000] ======= ifx_gpio_register (7,LEDC) ======= kernel module [ 0.565000] Lantiq LED Controller driver, version 1.0.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.574000] MEI CPE Driver, Version 1.4.1 [ 0.574000] [ 0.579000] (c) Copyright 2012, Lantiq Deutschland GmbH [ 0.579000] [ 0.586000] ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ### [ 0.586000] [ 0.593000] ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC [ 0.599000] [ 0.599000] ======= ifx_gpio_pin_reserve 40 (31,BUTTON) ======= kernel module [ 0.607000] [ 0.607000] ======= ifx_gpio_pin_reserve 3 (31,BUTTON) ======= kernel module [ 0.616000] Register ASC (UART) to PMCU. [ 0.620000] Lantiq ASC (UART) driver, version 1.0.9, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.628000] [ 0.628000] ======= ifx_gpio_register (20,USIF-UART) ======= kernel module [ 0.636000] [ 0.636000] ======= ifx_gpio_pin_reserve 11 (20,USIF-UART) ======= kernel module [ 0.645000] [ 0.645000] ======= ifx_gpio_pin_reserve 12 (20,USIF-UART) ======= kernel module [ 0.654000] [ 0.654000] ======= ifx_gpio_register (20,USIF-UART) ======= kernel module [ 0.662000] [ 0.662000] ======= ifx_gpio_pin_reserve 11 (20,USIF-UART) ======= kernel module [ 0.671000] [ 0.671000] ======= ifx_gpio_pin_reserve 12 (20,USIF-UART) ======= kernel module [ 0.680000] ttyUSIF0 at MMIO 0x1da00000 (irq = 117) is a USIF_UART [ 0.687000] Lantiq USIF-UART driver, version 1.1.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.701000] loop: module loaded [ 0.704000] ifx_nand_init [ 0.705000] [ 0.705000] ======= ifx_gpio_pin_reserve 23 (12,NAND) ======= kernel module [ 0.714000] [ 0.714000] ======= ifx_gpio_pin_reserve 24 (12,NAND) ======= kernel module [ 0.722000] [ 0.722000] ======= ifx_gpio_pin_reserve 13 (12,NAND) ======= kernel module [ 0.731000] [ 0.731000] ======= ifx_gpio_pin_reserve 48 (12,NAND) ======= kernel module [ 0.739000] [ 0.739000] ======= ifx_gpio_pin_reserve 49 (12,NAND) ======= kernel module [ 0.747000] Probe for NAND flash... [ 0.751000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) [ 0.761000] nand_read_bbt: Bad block at 0x000004200000 [ 0.765000] nand_read_bbt: Bad block at 0x0000142c0000 [ 0.770000] 15 cmdlinepart partitions found on MTD device ifx_nand [ 0.776000] using NEW partition bias algorithm. [ 0.781000] Creating 15 MTD partitions on "ifx_nand": [ 0.785000] 0x000000000000-0x000000040000 : "uboot" [ 0.792000] 0x000000040000-0x000003c40000 : "rootfs" [ 0.797000] 0x000003c40000-0x000004140000 : "kernel" [ 0.802000] 0x000004140000-0x000004240000 : "tmp1" [ 0.806000] 0x000004240000-0x000004440000 : "tmp2" [ 0.811000] 0x000004440000-0x000004540000 : "sysconfig" [ 0.816000] 0x000004540000-0x000004640000 : "ubootconfig" [ 0.822000] 0x000004640000-0x000004700000 : "fwdiag" [ 0.827000] 0x000004700000-0x000004a00000 : "lcdimage" [ 0.832000] 0x000004a00000-0x000004b00000 : "mfgconfig" [ 0.837000] 0x000004b00000-0x000004c00000 : "sipdata" [ 0.842000] 0x000004c00000-0x000008c00000 : "voice" [ 0.847000] 0x000008c00000-0x00001be00000 : "misc" [ 0.852000] 0x00001be00000-0x00001fa00000 : "rootfs2" [ 0.857000] 0x00001fa00000-0x00001ff00000 : "kernel2" [ 0.863000] [ 0.863000] ======= ifx_gpio_register (4,SSC) ======= kernel module [ 0.869000] Lantiq SSC driver, version 2.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.877000] PPP generic driver version 2.4.2 [ 0.881000] PPP Deflate Compression module registered [ 0.886000] PPP BSD Compression module registered [ 0.891000] PPP MPPE Compression module registered [ 0.895000] NET: Registered protocol family 24 [ 0.904000] IMQ driver loaded successfully. [ 0.907000] Hooking IMQ before NAT on PREROUTING. [ 0.912000] Hooking IMQ after NAT on POSTROUTING. [ 0.917000] IFX SWITCH API, Version 1.1.7.2 [ 0.921000] SWAPI: Registered character device [switch_api] with major no [81] [ 0.928000] Switch API: PCE MicroCode loaded !! [ 0.933000] Switch Auto Polling value = 0 [ 0.947000] GPHY FW load for A2x, chip id b!! [ 0.951000] GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR : 490000 [ 2.013000] IFX GPHY driver GE Mode, version ifxmips_vr9_gphy: V0.9 - Firmware: 8430 [ 2.019000] [ 2.019000] arc_kernel_module_init(31) DRV: Created Successfully [ 2.027000] res = 86d5cd80 [ 2.029000] [vectoring_init] g_ptm_net_dev = 00000000 mei_dsm_cb_func_hook=80212cf4 [ 2.038000] Registered led device: broadband_led [ 2.042000] Registered led device: internet_led [ 2.046000] Registered led device: ledc_2 [ 2.050000] Registered led device: ledc_3 [ 2.054000] Registered led device: ledc_4 [ 2.058000] Registered led device: ledc_5 [ 2.062000] Registered led device: ledc_6 [ 2.066000] Registered led device: ledc_7 [ 2.070000] Registered led device: ledc_8 [ 2.074000] Registered led device: ledc_9 [ 2.078000] Registered led device: ledc_10 [ 2.082000] Registered led device: ledc_11 [ 2.087000] Registered led device: wps_led [ 2.091000] Registered led device: ledc_13 [ 2.095000] Registered led device: ledc_14 [ 2.099000] Registered led device: usb2_link_led [ 2.103000] Registered led device: ledc_16 [ 2.107000] Registered led device: ledc_17 [ 2.112000] Registered led device: usb1_link_led [ 2.116000] Registered led device: fxo_act_led [ 2.121000] Registered led device: internet_red_led [ 2.125000] Registered led device: voip_led [ 2.130000] Registered led device: warning_led [ 2.134000] Registered led device: ledc_23 [ 2.138000] Lantiq LED driver, version 1.0.17, (c) 2001-2011 Lantiq Deutschland GmbH [ 2.146000] u32 classifier [ 2.148000] Performance counters on [ 2.152000] Actions configured [ 2.155000] nf_conntrack version 0.5.0 (1763 buckets, 7052 max) [ 2.162000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 2.169000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 2.177000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 2.183000] ip_conntrack_rtsp v0.6.21 loading [ 2.187000] xt_time: kernel timezone is -0000 [ 2.194000] IPv4 over IPv4 tunneling driver [ 2.198000] GRE over IPv4 tunneling driver [ 2.205000] ip_nat_rtsp v0.6.21 loading [ 2.207000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.213000] iptables target:TRIGGER __init [ 2.217000] TCP cubic registered [ 2.220000] NET: Registered protocol family 10 [ 2.228000] lo: Disabled Privacy Extensions [ 2.239000] tunl0: Disabled Privacy Extensions [ 2.248000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.252000] IPv6 over IPv4 tunneling driver [ 2.259000] sit0: Disabled Privacy Extensions [ 2.265000] NET: Registered protocol family 17 [ 2.268000] NET: Registered protocol family 8 [ 2.272000] atmpvc_init() failed with -17 [ 2.276000] lec.c: Apr 15 2015 15:28:25 initialized [ 2.281000] mpc.c: Apr 15 2015 15:28:22 initialized [ 2.286000] KOAM is loaded successfully. [ 2.290000] 802.1Q VLAN Support v1.8 Ben Greear [ 2.297000] All bugs added by David S. Miller [ 2.309000] VFS: Mounted root (squashfs filesystem) readonly on device 31:1. [ 2.315000] Freeing unused kernel memory: 176k freed [ 2.329000] Please be patient, while OpenWrt loads ... - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - - config restore - [read_sysconfig] read user config from sysconfig partition limg_addr = 0x4440000, part_size = 0x100000, offset = 0x0 Successfully read 74817 bytes of image sysconfig and write 74809 bytes into file /tmp/config.tgz [read_sysconfig] read_img from sysconfig successfully [extract_sysconfig] extract user config now config/ config/ntpclient config/xdsl-rc.conf config/firewall config/network config/passwd config/passwd- config/inittab config/glbcfg.dft config/ulogd.conf config/iproute2/ config/iproute2/rt_tables config/dropbear_key/ config/dropbear_key/authorized_keys config/dropbear_key/dropbear_dss_host_key config/dropbear_key/dropbear_rsa_host_key config/system config/arc-middle/ config/arc-middle/register/ config/arc-middle/register/002-mid_dsl.reg config/arc-middle/register/011-mid_ansmach.reg config/arc-middle/register/008-mid_usb.reg config/arc-middle/register/003-mid_switch.reg config/arc-middle/register/013-mid_iptv.reg config/arc-middle/register/005-mid_voip.reg config/arc-middle/register/006-mid_sys.reg config/arc-middle/register/010-mid_mon.reg config/arc-middle/register/012-mid_tda8029.reg config/arc-middle/register/009-mid_lte.reg config/arc-middle/register/001-mid_ccfg.reg config/arc-middle/register/007-mid_wlan.reg config/firewallExt/ config/inittab.noshell config/task_priority config/no_con_output.txt config/timezonelist config/www.pool.ntp.org_zone_de.html config/mapi_event.cfg config/.glbcfg config/dropbear config/rc.conf config/inittab.shell config/samba config/network-3g config/yafc_cfg config/timeserver config/system_boot_time config/cert/ config/cert/authorized_keys config/cert/Ftps/ config/cert/Ftps/pure-ftpd.pem config/cert/OpenVPN/ config/cert/dropbear_rsa_host_key config/cert/RootCA/ config/cert/RootCA/hr-rootca.req.pem config/cert/RootCA/hr-rootca.key.pem config/cert/RootCA/hr-rootca.crt.pem config/cert/dropbear_dss_host_key config/cert/WebServer/ config/cert/WebServer/hr-webserver.crt.pem config/cert/WebServer/hr-webserver.key.pem config/cert/WebServer/hr-webserver.req.pem config/hosts config/smbpasswd config/dhcp config/firewall_webdav.user config/firewall2.user config/firewall2_v6.user config/nat.user config/fwfast config/iptables_rebuild.save config/firewall.rebuild config/firewall.state config/snmpd config/group- config/group [extract_sysconfig] extract /tmp/config.tgz from sysconfig successfully [do_restore_cfg] Restore sysconfig successfully [handle_conf_compatibiltiy] prev_fwversion=AT904X-03.17.01.13, curr_fwversion=AT904X-03.17.01.13 [handle_conf_compatibiltiy] Same fwversion. Skip compatibility handling - init - log_level=0 Please press Enter to activate this console. [ 18.029000] yaffs: dev is 32505867 name is "mtdblock11" [ 18.033000] yaffs: passed flags "" [ 18.036000] yaffs: Attempting MTD mount on 31.11, "mtdblock11" [ 18.045000] yaffs: restored from checkpoint [ 18.047000] yaffs_read_super: isCheckpointed 1 Flash Partition for Answering Machine Already Initialized!! [resolv_update.sh] start, DNSMODE=0, $1=SYSTEM, $2=, $3=, $4=, $5= [resolv_update.sh] WANIF=ppp50, NETIF=ppp50, NETSECT=wan050, unit=50, wan_idx_1b=1 [resolv_update.sh] SYNCSVR=0, REMOVE_INTERFACE_DNS=0, DNS_ALL=, all_dns=, dns_lst= ., $*=SYSTEM [resolv_update.sh] end [ 25.012000] tun: Universal TUN/TAP device driver, 1.6 [ 25.016000] tun: (C) 1999-2004 Max Krasnyansky [ 27.975000] Netfilter messages via NETLINK v0.30. [ 28.484000] ctnetlink v0.93: registering with nfnetlink. [ 28.711000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) [ 28.806000] fuse init (API version 7.13) [misc] mount misc partition... [ 30.380000] yaffs: dev is 32505868 name is "mtdblock12" [ 30.384000] yaffs: passed flags "" [ 30.387000] yaffs: Attempting MTD mount on 31.12, "mtdblock12" [ 30.403000] yaffs: restored from checkpoint [ 30.405000] yaffs_read_super: isCheckpointed 1 [misc] misc partition is already initialized!! [ 30.576000] drv_sipo: module license 'Arcadyan' taints kernel. [ 30.581000] Disabling lock debugging due to kernel taint [ 30.591000] sipo_mod_init() [ 30.592000] sipo_dev_init() [ 30.595000] sipo_proc_init() [ 30.612000] [ 30.612000] ======= ifx_gpio_pin_reserve 29 (34,SIPO) ======= kernel module [ 30.619000] [ 30.619000] ======= ifx_gpio_pin_reserve 30 (34,SIPO) ======= kernel module [ 30.628000] [ 30.628000] ======= ifx_gpio_pin_reserve 39 (34,SIPO) ======= kernel module 21_sync_vpnserver script start 21_sync_vpnserver script end 22_sync_wireless script start 22_sync_wireless script end 25_sync_plc script start PrivacyEnabled@plc is missing, get from default StatusCheckTimer@plc is missing, get from default DetectionTimer@plc is missing, get from default 25_sync_plc script end [ 35.132000] RTK_SWAPI: Registered character device [rtl8367rb gigabit switch driver] with major no [177] [ 35.140000] rtl8367rb gigabit switch driver V1.0 init success!!! release at 2012/09/27 [dlna_share_folder_set] Twonky server has been shutdown, stopping dlna_share_folder_add >>> [ 51.654000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH [ 51.654000] [ 51.832000] [ 51.832000] Lantiq CPE API Driver version: DSL CPE API V4.15.2 [ 51.838000] [ 51.838000] Predefined debug level: 4 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] wan-mac-disable [setup_netdev.sh admin_sw_wan_mac] $1=0 [setup_netdev.sh admin_sw_wan_mac] power down [setup_netdev.sh admin_sw_wan_mac] switch_utility PortCfgSet 4 1 0 0 0 0 1 0 255 0 0 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] wan-phy-disable [setup_netdev.sh admin_sw_wan_phy] $1=0 [setup_netdev.sh admin_sw_wan_phy] power down [ifx_cpe_control_init.sh] detect_wan=1 [ifx_cpe_control_init.sh] cp /usr/bin-wan/auto-vdsl-rc.conf /etc/config/xdsl-rc.conf [ifx_cpe_control_init.sh] cp /usr/bin-wan/system_status /tmp/system_status [ifx_cpe_control_init.sh] wanphy_tc=1 [ifx_cpe_control_init.sh] wanphy_phymode=3 [ifx_cpe_control_init.sh] Next_xDSL_Mode=2 [ifx_cpe_control_init.sh] Next_xTM_Mode=PTM [ifx_cpe_control_init.sh] xDSL_SW_Forced_Reboot=0 [ifx_cpe_control_init.sh] xDSL_ADSL_Sub_Prefix=0 [ifx_cpe_control_init.sh] auto-sensing [ifx_cpe_control_init.sh] xDSL_Mgmt_Mode=Auto [ifx_cpe_control_init.sh] xDSL_MODE_VRX=adsl_b [ifx_cpe_control_init.sh] AUTOBOOT_ADSL=-a /tmp/adsl.scr [ifx_cpe_control_init.sh] AUTOBOOT_VDSL=-A /tmp/vdsl.scr [ifx_cpe_control_init.sh] xDSL_Mgmt_Mode=Auto, xDSL_SW_Forced_Reboot=0 [ifx_cpe_control_init.sh] XDSL_MULTIMODE=-M2, XTM_MULTIMODE= [ifx_cpe_control_init.sh] select_adsl_mode=1 [ifx_cpe_control_init.sh calc_xtse] CONFIG_FW_XDSL_ANNEX_B_* is on [ifx_cpe_control_init.sh calc_xtse] CONFIG_FW_XDSL_ANNEX_J is on @ Remove dms 0x0045 0x0000 0x0002 0000 0004 ifx_cpe_control_init.sh-----/opt/lantiq/bin/dsl_cpe_control -i10_00_10_00_00_04_01_07 -f /firmware/xcpe_hw.bin -M2 -A /tmp/vdsl.scr -a /tmp/adsl.scr -n /etc/init.d/xdslrc.sh [ifx_cpe_control_init.sh start] !!! SEAN !!! VECT_ENA is 1 [ 55.429000] [ 55.429000] MEI_VRX_DSM_DataInit, pMeiDev->meiERBbuf.pCallBackFunc=0x80212CF4 [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] switch-mac-disable [setup_netdev.sh disable_vrx_switch_ports] [disable_vrx_switch_ports] switch_utility PortCfgSet 0 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 1 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 2 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 3 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 4 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 5 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 7 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 8 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 9 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 10 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 11 0 0 0 0 0 1 0 255 0 0 [disable_vrx_switch_ports] switch_utility PortCfgSet 6 0 0 0 0 0 1 0 255 0 4 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] init_system [setup_netdev.sh init_system] [setup_netdev.sh init_system] $?=1 [setup_netdev.sh init_system] xDSL_MODE_VRX=vdsl [setup_netdev.sh init_system] Setting in flash is VDSL mode %% disable annex J: value should be 0x8f [setup_netdev.sh init_system] Enter PPA mode [ 59.316000] Loading E5 (MII0/1) driver, wanqos_en=8 ...... [ 59.324000] [init_local_variables] g_wanqos_en=8 [ 59.359000] [pkt_flooding_init] creating entry in /proc/eth/stop_flooding_packet [ 59.365000] Succeeded! [ 59.368000] PPE datapath driver info: [ 59.368000] Version ID: 64.3.3.1.0.1.1 [ 59.368000] Family : VR9 [ 59.368000] DR Type : Normal Data Path | Indirect-Fast Path [ 59.368000] Interface : MII0 | MII1 [ 59.368000] Mode : Routing [ 59.368000] Release : 0.1.1 [ 59.394000] PPE 0 firmware info: [ 59.394000] Version ID: 7.1.5.1.0.33 [ 59.394000] Family : VR9 [ 59.394000] FW Type : Standard [ 59.394000] Interface : MII0/1 + PTM [ 59.394000] Mode : reserved - 1 [ 59.394000] Release : 0.33 [ 59.394000] PPE 1 firmware info: [ 59.394000] Version ID: 7.2.1.6.2.0 [ 59.394000] Family : VR9 [ 59.394000] FW Type : Acceleration [ 59.394000] Interface : MII0 + MII1 [ 59.394000] Mode : Bridging + IPv4 Routing [ 59.394000] Release : 2.0 [ 60.022000] PPA API --- init successfully [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=DOWN [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= [ 60.655000] ifx_ppa_init - init succeeded [ 61.275000] device eth0 entered promiscuous mode [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] switch-mac-enable [setup_netdev.sh enable_vrx_switch_ports] [enable_vrx_switch_ports] switch_utility PortCfgSet 6 1 0 0 0 0 1 0 255 0 4 [enable_vrx_switch_ports] switch_utility PortCfgSet 0 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 1 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 2 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 3 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 4 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 5 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 7 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 8 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 9 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 10 1 0 0 0 0 1 0 255 0 0 [enable_vrx_switch_ports] switch_utility PortCfgSet 11 1 0 0 0 0 1 0 255 0 0 [ 63.063000] device eth0.66 entered promiscuous mode [ 63.114000] br-lan: port 1(eth0.66) entering forwarding state [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] switch-phy-disable [setup_netdev.sh admin_sw_phys] $1=0 [setup_netdev.sh admin_sw_phys] power down [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= [ 64.676000] device eth0.71 entered promiscuous mode [ 64.716000] br-lan1: port 1(eth0.71) entering forwarding state [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] init_ppadev [setup_netdev.sh init_ppadev] xDSL_MODE_VRX=vdsl [ 64.865000] ifx_ppa_init - init succeeded [ 65.136000] br-lan: port 1(eth0.66) entering disabled state [ 65.159000] br-lan1: port 1(eth0.71) entering disabled state [ 65.169000] WARNING: (MAC Address search Not Found) drivers/net/ifxmips_switch_api/ifx_ethsw_flow_api.c:IFX_FLOW_MAC_TableEntryRemove:1292 [ 65.187000] WARNING: (MAC Address search Not Found) drivers/net/ifxmips_switch_api/ifx_ethsw_flow_api.c:IFX_FLOW_MAC_TableEntryRemove:1292 [ 65.493000] device eth0 left promiscuous mode [ 65.501000] device eth0 entered promiscuous mode [ 65.507000] br-lan: port 1(eth0.66) entering forwarding state [ 65.516000] br-lan1: port 1(eth0.71) entering forwarding state [ 65.875000] WARNING: (MAC Address search Not Found) drivers/net/ifxmips_switch_api/ifx_ethsw_flow_api.c:IFX_FLOW_MAC_TableEntryRemove:1292 check to bring up pppoe 0 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] start_ethsw [setup_netdev.sh start_ethsw] [setup_netdev.sh start_ethsw_vdsl] [ 67.478000] This vid exists [create-ca-cert.sh] [ 68.598000] TAPI, Version 4.7.1.2, (c) 2001-2010 Lantiq Deutschland GmbH [ 68.783000] VoIP Driver, Rev. 1.0.0, (c) 2013-2015 Arcadyan Technology Corp. [ 68.789000] voip_proc_init() [ 68.792000] [ 68.792000] voip_init: VoIP registration completed successfully [ 68.810000] Si3050 Driver, Rev. 1.0r1 (polling mode), (c) 2010-2012 Arcadyan Technology Corp. [ 68.817000] [ 68.817000] ======= ifx_gpio_pin_reserve 22 (16,TAPI-FXO) ======= kernel module [ 68.825000] [ 68.825000] ======= ifx_gpio_pin_reserve 10 (16,TAPI-FXO) ======= kernel module [ 68.834000] [ 68.834000] ======= ifx_gpio_pin_reserve 17 (16,TAPI-FXO) ======= kernel module [ 68.843000] [ 68.843000] ======= ifx_gpio_pin_reserve 18 (16,TAPI-FXO) ======= kernel module [ 68.852000] [ 68.852000] ======= ifx_gpio_pin_reserve 16 (16,TAPI-FXO) ======= kernel module [ 68.861000] TRACE> [ 68.861000] daa_init: CHRDEV registration completed successfully [ 68.861000] [ 68.899000] br-lan: port 1(eth0.66) entering disabled state [ 68.923000] br-lan: port 1(eth0.66) entering forwarding state [resolv_update.sh] start, DNSMODE=0, $1=SYSTEM, $2=, $3=, $4=, $5= [ 69.764000] Lantiq MIPS34KEc MPS driver, version 2.2.3.1, (c) 2006-2010 Lantiq Deutschland GmbH [ 69.772000] Lantiq VMMC device driver, version 1.10.2.2, (c) 2006-2010 Lantiq Deutschland GmbH [resolv_update.sh] WANIF=ppp50, NETIF=ppp50, NETSECT=wan050, unit=50, wan_idx_1b=1 [resolv_update.sh] SYNCSVR=0, REMOVE_INTERFACE_DNS=0, DNS_ALL=, all_dns=, dns_lst= ., $*=SYSTEM check mtd wifi config ok! [resolv_update.sh] end [ 75.332000] br-lan1: port 1(eth0.71) entering disabled state [ 75.373000] br-lan1: port 1(eth0.71) entering forwarding state [resolv_update.sh] start, DNSMODE=0, $1=SYSTEM, $2=, $3=, $4=, $5= [resolv_update.sh] WANIF=ppp50, NETIF=ppp50, NETSECT=wan050, unit=50, wan_idx_1b=1 [resolv_update.sh] SYNCSVR=0, REMOVE_INTERFACE_DNS=0, DNS_ALL=, all_dns=, dns_lst= ., $*=SYSTEM [resolv_update.sh] end Wed Apr 15 06:30:21 CEST 2015 firewall.user finished [ 84.081000] Warnning!! syncmiimac is foreced to 0 in dual concurrent mode. [ 84.086000] RT3883iNIC: 802.11n WLAN MII driver v2.5.1.0 (Feb. 2, 2012) [ 84.093000] No card information file. [ 84.093000] Use default profile path. [ 84.100000] Update MAC(0)=88:03:55:e2:84:7a [ 84.105000] ============= Init Thread =================== [ 84.110000] RacfgTaskThread pid = 6979 [ 84.114000] RacfgBacklogThread pid = 6980 [ 84.118000] Org bridge hook = 803166c4 [ 84.121000] Change bridge hook = c088f2f8 [ 84.136000] ra0: Ralink iNIC at 0x0, 88:03:55:e2:84:7a [ 84.140000] Update MAC(0)=88:03:55:e2:84:7c [ 84.144000] ============= Init Thread =================== [ 84.150000] RacfgTaskThread pid = 6981 [ 84.153000] RacfgBacklogThread pid = 6982 [ 84.169000] rai0: Ralink iNIC at 0x0, 88:03:55:e2:84:7c [ 85.518000] iNIC Open ra0 [ 85.519000] [arc_reset_mii_gpio] *BSP_GPIO_P1_OUT=0xd066 [ 86.533000] Op mode = 1 [ 86.534000] Read profile[0] [ 87.612000] BssidNum=2 [ 87.614000] Read profile[1] [ 87.619000] BssidNum=2 [ 87.621000] rlk_inic_mbss_init ---> [ 87.623000] Register MBSSID IF (ra1) [ 87.639000] rlk_inic_mbss_init <--- [ 87.641000] Wait for boot done... [ 88.549000] RACFG_CMD_BOOT_NOTIFY [ 88.551000] Open file: /tmp/iNIC_ap.bin [ 88.554000] Open file: /tmp/iNIC_ap.dat [ 88.558000] Open file: /tmp/iNIC_e2p.bin [ 88.562000] Open file: /tmp/iNIC_ap1.dat [ 88.566000] Open file: /tmp/iNIC_e2p1.bin [ 89.549000] RACFG_CMD_BOOT_INITCFG(0) [ 89.553000] RACFG_CMD_BOOT_INITCFG(1) [ 89.556000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.561000] RACFG_CMD_BOOT_INITCFG(2) [ 89.564000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.569000] RACFG_CMD_BOOT_INITCFG(3) [ 89.574000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.578000] RACFG_CMD_BOOT_INITCFG(4) [ 89.582000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.587000] RACFG_CMD_BOOT_INITCFG(5) [ 89.590000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.594000] Send Init Cfg Data Done(6 packets) [ 89.599000] RACFG_CMD_BOOT_UPLOAD(0) [ 89.604000] RACFG_CMD_BOOT_UPLOAD(1) [ 89.608000] RACFG_CMD_BOOT_UPLOAD(2) [ 89.842000] [ 89.842000] CRC:01 08 14 18 07 3a 97 85 22 32 2e 35 2e 31 2e 33 22 00 00 00 32 30 31 34 31 32 31 32 00 00 00 00 00 00 00 00 58 cb 08 00 [ 89.856000] Send RT3883iNIC Firmware Done [ 89.858000] =================================== [ 89.863000] version: "2.5.1.3" [ 89.866000] size: 576344 bytes [ 89.869000] date: 20141212 [ 89.872000] =================================== [ 89.872000] [ 89.878000] Send STARTUP to RT3883iNIC [ 89.882000] Close Firmware file [ 89.885000] RACFG_CMD_BOOT_STARTUP [ 98.659000] Get concurrent card MAC address:88:03:55:e2:84:7a88:03:55:e2:84:7c [ 98.664000] Update MAC(0)=88:03:55:e2:84:7a [ 98.669000] Update MAC(1)=88:03:55:e2:84:7b [ 98.673000] Update MAC(0)=88:03:55:e2:84:7c [ 98.677000] Warning! MAC addr not equal to MII master => set MiiMasterMac=88:03:55:e2:84:74 [ 98.685000] You've assigned a different MAC. [ 98.731000] WARN! IOCTL 8bef ignored (interface not opened yet) [ 98.816000] setup MBSS[1] success [ 98.818000] ra1: ==>>> MBSS_VirtualIF_Open [ 98.857000] iNIC Open rai0 [ 98.858000] Op mode = 1 [ 98.861000] rlk_inic_mbss_init ---> [ 98.864000] Register MBSSID IF (rai1) [ 98.880000] rlk_inic_mbss_init <--- [ 98.964000] setup MBSS[1] success [ 98.966000] rai1: ==>>> MBSS_VirtualIF_Open setting 2.4G Main SSID setting 2.4G Second SSID setting 5G Main SSID setting 5G Second SSID [ralink3883] start to remove /tmp/ralink3883Starting [ 113.004000] tp904_mod_init() [ 113.006000] tp904_dev_init() [ 113.009000] tp904_proc_init() [ 113.012000] [ 113.012000] ======= ifx_gpio_pin_reserve 1 (33,TP) ======= kernel module [ 113.020000] [ 113.020000] ======= ifx_gpio_pin_reserve 14 (33,TP) ======= kernel module [ 113.028000] [ 113.028000] ======= ifx_gpio_pin_reserve 19 (33,TP) ======= kernel module [ 113.167000] wdt_ioctl:enable watch dog timer! debug: HAS_LTE=No [ 113.462000] lcd904_mod_init() [ 113.464000] lcd904_dev_init() [ 113.467000] lcd904_fb_init() [ 113.470000] lcd904_proc_init() [ 113.473000] [ 113.473000] ======= ifx_gpio_pin_reserve 6 (32,LCD) ======= kernel module [ 113.481000] [ 113.481000] ======= ifx_gpio_pin_reserve 28 (32,LCD) ======= kernel module [ 113.489000] [ 113.489000] ======= ifx_gpio_pin_reserve 31 (25,LED) ======= kernel module [ 115.468000] [ 115.468000] ======= ifx_gpio_register (27,EXIN) ======= kernel module INSERT ARCUSB KERNEL MODULE [ 116.607000] ARCUSB: Kernel Module Initializing... [ 116.610000] ARCUSB: Init and reserve GPIOs... [ 116.615000] [ 116.615000] ======= ifx_gpio_pin_reserve 33 (8,USB) ======= kernel module [ 116.623000] arcusb_gpio_initialize> check poing 'h' [ 117.076000] TRACE> isdn_init [ 117.076000] ISDN Driver, Rev. 1.0r1, (c) 2011-2013 Arcadyan Technology Corp. [ 117.085000] [ 117.085000] ======= ifx_gpio_pin_reserve 15 (16,TAPI-FXO) ======= kernel module [ 117.093000] [ 117.093000] ======= ifx_gpio_pin_reserve 20 (16,TAPI-FXO) ======= kernel module [ 117.102000] [ 117.102000] ======= ifx_gpio_pin_reserve 9 (16,TAPI-FXO) ======= kernel module [ 117.111000] [ 117.111000] ======= ifx_gpio_pin_reserve 5 (16,TAPI-FXO) ======= kernel module [ 117.120000] isdn_proc_init() [ 117.122000] TRACE> [ 117.122000] isdn_init: CHRDEV registration completed successfully [ 117.122000] #### start PPP Vid detection #### Boot Wan detection #### start Auto Wan detection [autowandetect main] [get_detect_wan_mode] get detect_wan=1 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] lan-phy-enable [setup_netdev.sh admin_sw_lan_phys] $1=1 copy gConfig and gSetting begin. [ 121.632000] copy gConfig and gSetting end. [ 121.638000] ARCUSB: Init Host Controllers and others... [ 121.643000] [USB] UsbSMem: need 58400 bytes [ 121.647000] [USB] UsbMMem: need 39936 bytes [ 121.651000] [USB] UsbLMem: need 126976 bytes [ 121.656000] [USB] UsbSMem: 842C0000H ~ 842CE41FH [ 121.660000] [USB] UsbMMem: 842D0000H ~ 842D9BFFH [ 121.665000] [USB] UsbLMem: 842E0000H ~ 842FEFFFH [ 121.670000] [USB] UsbSMemLink: 84282000H ~ 84283C6FH [ 121.674000] [USB] UsbMMemLink: 85659000H ~ 85659603H [ 121.679000] [USB] UsbLMemLink: 851F1800H ~ 851F1A57H [ 121.685000] arcusb_mem: at 0x83800000 allocate 1052304 bytes ... OK [ 121.691000] arcusb_mem: at 0x83920000 allocate 119540 bytes ... OK [ 121.697000] arcusb_mem: short-cut, 8421120 bytes pre-allocated, UsbMPool @ 87400000 [ 121.704000] arcusb_mem: at 0x839c0000 allocate 40760 bytes ... OK [ 121.711000] arcusb_mem: at 0x83a00000 allocate 1131520 bytes ... OK [ 121.717000] arcusb_mem: at 0x83bff000 allocate 1260 bytes ... OK [ 121.723000] [USB] Small Un-Cached Memory(5977): 83800020 ~ 83900D4F [ 121.729000] [USB] Medium Un-Cached Memory(2038): 87400020 ~ 87C05EDF [ 121.735000] [USB] Large Un-Cached Memory(63): 83A00020 ~ 83B0BC1F [ 121.742000] setUsbPciInfo() cpu_to_usb_addr_shift[5]:0x00000000, usb_to_cpu_addr_shift[5]:0x00000000 [ 121.751000] usb_pci_probe() Found Synopsis OTG-1, baseAddr:0xbe101000, IRQ:54 [ 121.758000] setUsbPciInfo() cpu_to_usb_addr_shift[6]:0x00000000, usb_to_cpu_addr_shift[6]:0x00000000 [ 121.767000] usb_pci_probe() Found Synopsis OTG-2, baseAddr:0xbe106000, IRQ:48 [ 121.774000] usb_hcd_init() probe PCI function:2 !! [ 121.779000] usb_host_power_set() Previous power off:0, current time:121779 [ 121.786000] usb_host_power_set(1) min time delay:6000, current delay:121779 [ 121.793000] usb_host_power_set(2) min time delay:6000, current delay:121793 [ 121.800000] usb_hcd_init() func(0):0 [ 121.803000] usb_hcd_init() func(1):0 [ 121.807000] usb_hcd_init() func(2):0 [ 121.810000] usb_hcd_init() func(3):0 [ 121.814000] usb_hcd_init() func(4):0 [ 121.817000] usb_hcd_init() func(5):1 [ 121.821000] localhc_init() install otg driver(host_drv = 0xC20B6090, otg_driver=0xC20B6090). [ 121.829000] usb_hcd_init() func(6):1 [ 121.833000] localhc_init() install otg driver(host_drv = 0xC20B6090, otg_driver=0xC20B6090). [ 121.841000] usb_hcd_init(): succ. [setup_netdev.sh admin_sw_lan_phys] power up [setup_netdev.sh admin_sw_lan_phys] switch_utility MDIO_DataWrite 0 0 0xf7ff [setup_netdev.sh admin_sw_lan_phys] switch_utility MDIO_DataWrite 1 0 0xf7ff [setup_netdev.sh admin_sw_lan_phys] switch_utility MDIO_DataWrite 17 0 0x1040 [setup_netdev.sh admin_sw_lan_phys] switch_utility MDIO_DataWrite 18 0 0xf7ff [setup_netdev.sh admin_sw_lan_phys] switch_utility MDIO_DataWrite 5 0 0xf7ff Trigger UP TR069 Module. [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] wan-mac-enable [setup_netdev.sh admin_sw_wan_mac] $1=1 [setup_netdev.sh admin_sw_wan_mac] power up [setup_netdev.sh admin_sw_wan_mac] switch_utility PortCfgSet 4 1 0 0 0 0 1 0 255 0 0 [ 123.409000] Run a kernel thread "UsbSysInitTask" success (PID: 9512) (nice 0) (kdata 0x00000000) [ 123.416000] arcusb_chrdev: allocate major number 245 success. [ 123.422000] [ 123.422000] [ 123.422000] arcusb_chrdev: add a new char device "umtsCS" OK. [ 123.422000] [ 123.432000] [ 123.432000] [ 123.432000] arcusb_chrdev: add a new char device "lp0" OK. [ 123.432000] [ 123.452000] Run a kernel thread "xSpeedTask" success (PID: 9727) (nice 0) (kdata 0x00000000) lcdwizard(init.d) : boot lcdwizard(init.d) : start : check if (mptest) [ 123.484000] Run a kernel thread "FlushCacheTask" success (PID: 9729) (nice 0) (kdata 0x00000000) lcdwizard(init.d) : no mptest, check if (/dev/fb0) lcdwizard(init.d) : /dev/fb0 is exist, goto /usr/sbin, execute lcdwizard lcdwizard(init.d) : start : exit if [ 123.533000] Run a kernel thread "usb_hc_timer_task" success (PID: 9735) (nice 0) (kdata 0x00000000) [ 123.596000] initVoiceBufferQueue: reset arcusb_voice_previous_timestamp (error correct -1 ms) [ 123.603000] initVoiceBufferQueue: reset arcusb_voice_previous_timestamp (error correct -1 ms) [ 123.613000] initVoiceBufferQueue: reset arcusb_voice_previous_timestamp (error correct -1 ms) [ 123.621000] initVoiceBufferQueue: reset arcusb_voice_previous_timestamp (error correct -1 ms) START ARCADYAN USB SUBSYSTEM [ 124.149000] [USB] dwc3884_start() Core id:0, funcIdx:5 [ 124.152000] *IFX_CGU_IF_CLK 10e0000b [ 124.257000] setSynopsisPower() set power... [ 124.260000] setSynopsisPower() USB PHY configurations... [ 124.265000] setSynopsisPower() set PMU... [ 124.274000] [USB] dwc3884_start() DWC3884 core version:0x4F54281A, 2.81a, channel:16 [ 124.280000] [USB] dwc3884_reset(XR9) Reset In, core_id:0 [ 124.286000] [USB] dwc3884_reset(VR9) IFX_RCU_USB0_CFG:0xBF203018, var:0x00001480 [ 124.293000] [USB] dwc3884_reset(VR9) IFX_RCU_USB1_CFG:0xBF203034, var:0x00001400 [ 124.300000] [USB] dwc3884_reset(VR9) IFX_RCU_RST_REQ:0xBF203010 [ 125.820000] [USB] dwc3884_reset() rstctl:0xBE101010 [ 127.503000] [USB] dwc3884_start() intsts:0xBE101014, var:0x54000029 [setup_netdev.sh] ETH_WAN_PORT=4, CONFIG_ETH_WAN_PORT=4, CPU_PORT=6 [setup_netdev.sh] wan-phy-enable [setup_netdev.sh admin_sw_wan_phy] $1=1 [setup_netdev.sh admin_sw_wan_phy] power up [setup_netdev.sh admin_sw_wan_phy] switch_utility MDIO_DataWrite 19 0 0x1040 Current LTE prefernet config 8 Current UMTS prefernet config 0 Auto correct umts_allow_mid@lte value Auto correct lte_allow_mid@lte value IPV6 module disable, apply 1 to LTE data. IPV6 module disable, apply 1 to LTE voice. IPV6 module disable, apply 1 to UMTS data. [ 129.631000] ARCUSB: setup "backup_mode" = "0" successfully. [ 129.635000] ARCUSB: set backup_mode to 0 [ 129.679000] ARCUSB: setup "lte_allow_mid" = "-1" successfully. [ 129.708000] ARCUSB: setup "umts_allow_mid" = "2,35,38,42,45" successfully. [ 129.713000] ARCUSB: Add mid:35, Success !! [ 129.717000] ARCUSB: Add mid:38, Success !! [ 129.722000] ARCUSB: Add mid:42, Success !! [ 129.726000] ARCUSB: Add mid:45, Success !! [ 129.843000] ARCUSB: setup "lte_sim_lock_ops" = "2,26202,26209" successfully. [ 129.849000] ARCUSB: Add PLMN-ID:26202, Success !! [ 129.853000] ARCUSB: Add PLMN-ID:26209, Success !! [ 130.070000] ARCUSB: setup "umts_sim_lock_ops" = "-1" successfully. [ 130.099000] ARCUSB: setup "dataAPN" = "fixed.data.vodafone.de" successfully. [ 130.132000] ARCUSB: setup "voiceAPN" = "fixed.voice.vodafone.de" successfully. [ 130.173000] ARCUSB: setup "PIN" field FAILED!!!!! [ 130.192000] ARCUSB: setup "PINenb" field FAILED!!!!! [ 130.210000] ARCUSB: setup "dataIP_type" = "1" successfully. [ 130.214000] ARCUSB: set dataIP_type as 1 [ 130.260000] ARCUSB: setup "umtsAPN" = "web.vodafone.de" successfully. [ 130.348000] ARCUSB: setup "umtsPIN" field FAILED!!!!! [ 130.369000] ARCUSB: setup "umtsPINenb" = "0" successfully. [ 130.373000] ARCUSB: set umtsPINenb to 0 [ 130.416000] ARCUSB: setup "umtsPhoneNumer" field FAILED!!!!! [ 130.480000] ARCUSB: setup "umtsIdleTime" field FAILED!!!!! moremsg@lte was existed, its value is 0x00000000 expert_mode@lte was existed, its value is off manual_mode@lte was existed, its value is off [ 130.520000] ARCUSB: setup "explore" = "on" successfully. [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=DOWN [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= #################################################### BOOT FROM IMAGE 1 FW Version: AT904X-03.17.01.13 #################################################### [lcdwizard] create_LCD_socket(30391) start [lcdwizard] create_LCD_socket(30410) end : return 7 sh: missing ] [ 137.561000] VPE loader: VPE1 running successfully [ 137.831000] voip_initialize_cmd [ 137.833000] TRACE> prodaa_initialize_cmd: Seting up timers, Hz: 1000 [ 137.833000] TRACE> prodaa_setup:ENTER [ 137.873000] TRACE> prodaa_init begin now [ 137.906000] TRACE> prodaa_init: Line-Side Device Status 40 [ 137.910000] TRACE> Port 2 sytem-side revision 45, line-side revision 6 [ 137.915000] TRACE> prodaa_setup:EXIT [ 137.922000] [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= Run a kernel thread "usb_hc_timer_child_task" success (PID: 10712) (nice 0) (kdata 0xC20BD650) [ 142.221000] stollmann_isdn: loading module [ 142.224000] Stollmann E+V GmbH ISDN-Stack V5.005J Apr 2 2014 [ 142.230000] (c) Copyright Stollmann E+V GmbH [ 142.234000] isdn_avr.lnxhwInit (c297d3e0): enter .. [ 142.239000] ISDN_initialize: Initialize BSP here.... [ 142.403000] TRACE> T-SMINTI r3F(CHIP ID)= 0x20 [ 142.403000] TRACE> T-SMINTI r7D(FW VERSION)= 0x3e [ 142.407000] [ 142.413000] 0000 isdn_avr.lnxhwAVRDetect IPACX Chip-ID=0x20 [ 142.418000] isdn_avr.lnxhwAVRDetect: iNbr=0, IntNbr=0 [ 142.423000] isdn_avr.lnxhwAVRDoPostInit: ISDN-CHIP(1) found at address=0xb0000000 [ 142.446000] isdn_avr.lnxhwAVRInterruptDeferredIntProcStart: exit .. [ 142.451000] isdn_avr.lnxhwAVRDoPostInit: iLineIF=1 protocol=0xc3 IInit=1 l1Mode=0 S0BusConf=0 g711Law=1(disable=0) [ 142.461000] isdn_avr.lnxhwAVRDoPostInit: iLineIF=2 protocol=0xc2 IInit=3 l1Mode=2 S0BusConf=1 g711Law=1(disable=0) [ 142.479000] isdn_avr.hwInterruptInit: iIndex=0 [ 142.482000] isdn_avr.lnxhwAVRRequestInterruptVector: request_irq; idx=0, lvl=0, flags=20, intHandler=c297d000 [ 142.492000] ISDN_request_irq: 0 c297d000 20 isdn_avr c2999f98 [ 142.498000] isdn_avr.hwInterruptInit: rcvd irq for lvl=0 for ISDN_DEVICE 0 [ 142.514000] IFX_DRV_HDLC_Open: 0 (/dev/vmmc15) [ 142.539000] IFX_DRV_HDLC_Open: 1 (/dev/vmmc16) [ 142.551000] isdn_avr.lnxhwAVRDoPostInit/firmwareStart() OK. [ 143.590000] capifs: Rev 1.1.2.3 webdav_stop execute [twonky_database_set] twonky_database_set called by <0> [twonky_database_set] wrong caller, stop anyway... *****0. entering Samba start... (samba.init) *****9. Samba Stop. [ 144.661000] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) httpd_init: get MAPI tid=4997456 CLOCK_MONOTONIC, resolution=0.1 System clock_res=1000000, clock_hz=1000 [ 147.701000] TRACE> isdn_open [ 147.701000] TRACE> isdn_initialize_cmd [ 147.704000] TRACE> isdn_initialize_cmd: Seting up timers, Hz: 1000 [ 147.708000] [ 148.038000] [ 148.038000] >>>>>> usbd_new_device: adding unit bus:1, addr=1, rev=0200, class=9, subclass=0, protocol=1, maxpacket=64, len=18, speed=3 [ 148.038000] [ 148.038000] usbd_new_device() addr:1, vid:0x058b, pid:0xf002, devFlag:0x0000 [ 148.060000] usbd_probe_and_attach(Hub)> Reopen STATIC default pipe OK [ 148.067000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 148.073000] usbd_open_pipe_intr: ipipe=842c0f00 repeat=0 xfer=a7ae1aa0 [ 148.498000] usbd_probe_and_attach,probe 1! [ 148.500000] [USB] dwc3884_start() Core id:1, funcIdx:6 [ 148.511000] [USB] dwc3884_start() DWC3884 core version:0x4F54281A, 2.81a, channel:16 [ 148.517000] [USB] dwc3884_reset(XR9) Reset In, core_id:1 [ 148.522000] [USB] dwc3884_reset() rstctl:0xBE106010 [ 148.703000] [USB] dwc3884_start() intsts:0xBE106014, var:0x54000029 mapi_ansmach_phone_grtMsg_save(3571): md5_ori=996be7589f67cca3ae1e4263a91dce91 (/tmp/default_grtmsg_check.711) mapi_ansmach_phone_grtMsg_save(3572): md5_new=996be7589f67cca3ae1e4263a91dce91 (/tmp/usb/gm_148920.g711a) mapi_ansmach_phone_grtMsg_save(3575): md5 of grtmsg is the same... skip save operation [ 151.229000] [ 151.229000] [ 151.229000] >>>>>> usbd_new_device: adding unit bus:2, addr=1, rev=0200, class=9, subclass=0, protocol=1, maxpacket=64, len=18, speed=3 [ 151.229000] [ 151.229000] usbd_new_device() addr:1, vid:0x058b, pid:0xf002, devFlag:0x0000 [ 151.252000] usbd_probe_and_attach(Hub)> Reopen STATIC default pipe OK [ 151.259000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 151.265000] usbd_open_pipe_intr: ipipe=842c1540 repeat=0 xfer=a7ae3ae0 [ 152.014000] usbd_probe_and_attach,probe 1! [ 152.025000] Run a kernel thread "usb_explore_task" success (PID: 11602) (nice 0) (kdata 0xC20BD650) [ 152.032000] startExplore() usb explore task run-up, slot:0, tsk_id:11602, reason:0 [ 152.040000] usb_hc_install_interrupt() Install OTG-1 interrupt 54 [ 152.046000] usb_hc_install_interrupt() Install OTG-2 interrupt 83 [ 152.052000] USB Module: Version 2.0.0 build Apr 15 2015 14:39:10 [ 152.052000] usb_explore_task() Begin ... [ 152.065000] [ 152.065000] [ 152.068000] *************************************************** [ 152.073000] * THIS IS A STABLE ARCUSB SUBSYSTEM. * [ 152.079000] * Apr 15 2015 14:39:27 * [ 152.085000] *************************************************** [ 152.085000] [ 152.093000] usb_explore_task> START USB_EXPLORE_TASK... [absread] : read() fails, return 0 threadMask=3 httpd: listen at 192.168.2.1:80 HTTPD: can't get IPV6 LLA of br-lan interface HTTPD: can't get IPV6 ULA of br-lan interface [2051] get MAPI tid=5251800(pid=11879) [1026] get MAPI tid=5247592(pid=11878) /usr/sbin/httpd-brn: initialization complete! main: http_redir_init initialization complete! mounted_num = [webdav_folder_set] setting webdav default folder >>> 0 0 DRV_DATA = 0:0:1:ST:16GB:AA627090403000000183:sda:: DRV_DATA = DRV_DATA = DRV_DATA = DRV_DATA = [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS= [xdslrc.sh] platform=VR9,detect_wan=1 [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode=PTM [xdslrc.sh] DSL_ADSL_SUB_PREF=, DSL_TC_LAYER_STATUS= [xdslrc.sh] DSL_EFM_TC_CONFIG_US=, DSL_EFM_TC_CONFIG_DS=